Diffusion welding:
   Diffusion welding joins parts by holding them in intimate contact at a given temperature and pressure for a period of time, allowing atoms at the contact faces to diffuse into each other and form the bond. The main factors affecting the process and joint quality are temperature, pressure, diffusion time and surface roughness. The higher the welding temperature, the faster the atomic diffusion; the welding temperature is generally 0.5–0.8 times the material's melting point. Depending on the material and the joint quality required, diffusion welding can be performed in vacuum, in shielding gas or in solvent, with vacuum diffusion welding the most widely used. To speed up the process, relax surface-roughness requirements or prevent harmful microstructures in the joint, an intermediate interlayer of specific composition, about 0.01 mm thick, is often added between the welding surfaces. Diffusion welding uses low pressure; the workpiece undergoes no macroscopic plastic deformation, making it suitable for precision parts that will not be machined after welding. Diffusion welding can be combined with other thermal processes into composite processes such as thermal-deformation diffusion welding, powder-sintering diffusion welding and superplastic-forming diffusion welding. These combined processes not only greatly raise productivity but also solve problems that a single process cannot — for example, various titanium-alloy components on supersonic aircraft are made by superplastic-forming diffusion welding. Diffusion-welded joints can match the parent metal in performance, and the process is especially suited to welding dissimilar metals, non-metals such as graphite and ceramics, dispersion-strengthened superalloys, metal-matrix composites and porous sintered materials. It is widely used in making reactor fuel elements, honeycomb structural panels, electrostatic accelerator tubes, blades, impellers, dies, filter tubes and electronic components.
   Diffusion welding is a welding method in which, at a given temperature and pressure, the welding surfaces of the materials to be joined are brought into contact, the physical contact is enlarged through microscopic plastic deformation or a trace amount of liquid phase at the weld interface, until the gap is within (1– 5)×10⁻⁸ cm (so that interatomic attraction takes effect and metallic bonds can form), and then long, continuous mutual atomic diffusion and interpenetration produce a metallurgical bond.
   Clearly, for ordinary wire-harness welding, diffusion welding is far too costly.
    High-frequency welding:
  High-frequency welding uses solid resistance heat as the energy source. During welding, the resistance heat generated by high-frequency current inside the workpiece heats the surface layer of the weld zone to melting or a near-plastic state, and then upsetting force is applied (or not) to bond the metal. It is therefore a solid-phase resistance welding method. By the way high-frequency current generates heat in the workpiece, it is divided into contact high-frequency welding and induction high-frequency welding. In contact high-frequency welding, the high-frequency current enters the workpiece through mechanical contact. In induction high-frequency welding, the high-frequency current induces a current in the workpiece through coupling with an induction coil outside the workpiece. High-frequency welding is a highly specialized process requiring dedicated equipment for each product. It is highly productive, with welding speeds up to 30 m/min. It is mainly used for longitudinal or spiral seams when making pipe.
   Clearly, high-frequency welding is not suitable for fine wire harnesses.
    Cold pressure welding:
    Under pressure and deformation, the oxide film on the workpiece contact faces is broken up and squeezed out, purifying the weld joint. The pressure applied generally has to exceed the material's yield strength to produce 60–90% deformation. Pressure can be applied by slow extrusion, rolling or impact, or in several passes to reach the required deformation.
   Cold pressure welding needs no heating and no filler, and the equipment is simple; its main process parameters are already fixed by the die dimensions, so it is easy to operate and automate, with stable weld quality, high productivity and low cost. No flux is used, so joints do not corrode; the joint temperature does not rise during welding and the material's crystal structure is unchanged, making it especially suitable for dissimilar metals and for some metals and products that hot welding methods cannot handle. Cold pressure welding has become one of the few most important welding methods in the electrical industry, the aluminum products industry and space welding.
   Metal debris can accumulate on the working surfaces of the cold pressure welder and its dies and must be removed regularly. If compressed air is available, blow the debris off with it. For a thorough cleaning, remove the dies from the welder, take apart the four die blocks and inspect each block carefully under a magnifier to make sure all trace debris is removed. Take care when disassembling the dies — the small springs are easily lost. Unclean die surfaces will cause wires to slip in the dies during termination, leading to weld failure. After servicing, the die working surfaces must be completely free of any grease.
   Cold pressure welding equipment is simple, the process is easy, and working conditions are good. But it needs large extrusion forces, so equipment becomes bulky for large-section workpieces, and lap welding leaves deep indentations on the workpiece surface, which limits its application to some extent.
   Cold pressure welding is therefore not the perfect choice for wire-harness welding, either.