The most common method for welding thermoplastic parts is ultrasonic welding. It uses low-amplitude, high-frequency (ultrasonic) vibration energy to generate, through surface and molecular friction, the heat needed to weld and join the plastic parts. (Sinusoidal ultrasonic vibration.) Ultrasonic welding occurs in the 20–50 kHz frequency range, with typical amplitudes of 15–60 μm. Sonic frequencies as low as 15 kHz (with higher amplitude) are sometimes used for larger parts or softer materials. The weld cycle typically takes 0.5–1.5 s. Process variables include weld time, horn position, and weld pressure. Ultrasonic welding equipment is generally used for small- and medium-sized thermoplastic parts, while very large parts can be joined with multi-point welding.
Ultrasonic welding can be controlled by weld time, weld position (collapse distance), or weld energy. Additional control of weld pressure and cooling time is also provided. Ultrasonic welding equipment generally operates at either 20 kHz or 40 kHz, with 20 kHz units being more common.
Joint design: the first—and most common—category uses ultrasonic vibration perpendicular to the surfaces being joined. Butt joints and Z-shaped joints fall into this category and suit most polymers. The second category of ultrasonic joints uses vibration parallel to the joint surface, creating a shear condition; various shear and interlocking joints fall into this category.
Energy directors work best with amorphous materials; larger energy directors can be used in some non-hermetic semi-crystalline materials. A rough or textured surface on the lower part improves weld quality, weld strength, and ease of welding. Many other textured joint profiles are also feasible. Flash problems can be reduced by incorporating flash traps into the joint design; as a rule, flash traps are designed with at least 10% excess volume capacity.
Interference joints: designed to block the melt or keep it within the melt zone so as to minimize flash. Interference joints are useful for semi-crystalline plastics such as nylon. Because the joint structure is more complex, interference joints require relatively tight part-fit tolerances. Compared with triangular energy-director welding, the larger joint structure also requires additional amplitude and weld energy.
Part alignment: a simple butt joint provides no means of aligning or centering the parts. Alignment is better achieved with molded locating pins or studs. Z-shaped joints, by contrast, are self-aligning, offer good tensile strength in use, improved shear-load resistance, and eliminate external flash.
Tongue-and-groove joints provide both shear and tensile strength. This joint is self-aligning, but the wall thickness in the joint area must be relatively large to accommodate the design. Part tolerances are also relatively tight. Intermittent ribs improve joint alignment.
When designing joints, shear joints are generally recommended. Round and rectangular parts requiring high-strength, high-quality joints all use shear joints. A shear joint has overlapping part walls; as the joint is welded and the parts telescope together, the overlap creates interference and localized shear. To aid part alignment, the joint includes a lead-in. To concentrate melting energy, the apex of the bead on one side is reduced at the initial contact surface. Because the molten material's temperature stays consistent across the entire contact surface, both surfaces melt uniformly during welding. For depths of 1.0–2.0 mm, use tolerance values in the 0.13–0.5 mm range. To prevent external sidewall warpage caused by tolerances during welding, vertical parts should be as shallow as possible; however, a tongue-and-groove joint improved with a shear part on one side can be used with deeper drawn parts to provide a mid-wall joint that minimizes tolerance-induced sidewall warpage.
Scarf joints have a 30°–60° angle and should be assembled within ±1°. An additional 0.10–0.25 mm tolerance for melt-zone material thickness produces the weld bead and flash. When flash is functionally or aesthetically unacceptable, a flash collector is used.
Welding with an embedded sealing device: reliable sealing can also be achieved with an embedded elastomeric O-ring or resilient gasket. The joint part is fitted with an elastic ring to improve the sealing reliability achievable with ultrasonic welding, or for use where continuous peripheral welding is not possible.
PreviousUltrasonic Lace Sewing Machine Maintenance and InspectionNextABS Plastic Characteristics and Uses