Vibration welding:
    Vibration welding (usually linear vibration welding) is a friction welding process that uses an electromagnetic drive to create relative (linear) motion between two plastic parts. During vibration welding, the parts reciprocate under pressure, generating heat that raises the joint material above its melting point; once the material is fully molten, the motion stops and the plastic solidifies under pressure to form a permanent weld. Vibration welding can join the vast majority of thermoplastics — injection-molded, extruded, blow-molded , thermoformed, stamped or foam parts can all be vibration-welded. It is especially suited to crystalline thermoplastics such as acetal, polyethylene, nylon and polypropylene, which are difficult to weld by ultrasonic or hot-melt methods. Moisture-absorbing polyamides must be dried before ultrasonic welding, but vibration welding is unaffected by material moisture absorption. Vibration welding can also join dissimilar material combinations, though the addition of certain fillers or pigments may reduce joint strength. When welding long or thin unsupported parts, reinforcement is needed to prevent bending during welding. For parts where weld appearance matters, a flash cover should be included in the design.
    The main advantages of vibration welding are welding large, complex linear joints at very high production speeds and welding many parts simultaneously. Cycle times are short, the process is insensitive to surface preparation and controllable, and there is no degradation of the interface material from overheating. Its main disadvantages: it is limited to flat-seam parts and is not suitable for low-modulus thermoplastics such as certain thermoplastic elastomers.
    Vibration welding is very widely used in the automotive industry. One of its most valuable applications is the two-piece plastic bumper. The basic structure is a long, curved U -section bumper welded to a rear reinforcement plate. The joint is 115 m long, with 70 parts welded per hour. The structure is lightweight, low-cost and aerodynamically efficient. Other vibration welding applications include: intake manifolds, fuel tanks, fuel pumps, expansion valves, instrument panels, air ducts, rear parcel shelves, interior door panels, radiator grilles, headlamps, tail lamp assemblies, fuel filler inlets, spoilers, cowl covers, brake components, power steering components, vacuum tanks, interior trim parts and devices, and sealing of air ducts to the inner surface of instrument panels.
    Spin welding:
    Spin welding belongs to the friction welding family. Plastic spin welding is similar to metal friction welding: during spin welding, the parts to be joined rotate at high speed relative to each other under axial force; the resulting frictional heat melts the plastic. After the relative motion stops, the molten plastic solidifies under pressure to form the weld. Unlike metal friction welding, where no melting occurs, in spin welding the plastic melts at the joint interface. The basic parameters of spin welding are: rotation speed, joint pressure and rotation time. The rotation speed is set according to material type and joint diameter.
    Spin welding is divided into inertia friction welding (decreasing speed) and continuous-drive friction welding (constant speed during heating) . Thin-walled parts cannot withstand the large axial force of inertia friction welding, so continuous-drive friction welding is recommended. Spin welding can weld all kinds of amorphous and semi-crystalline plastics; many plastics that cannot be ultrasonically welded can be spin-welded. The static strength of a spin weld can reach 50 %–95 % of the base material (depending on the material), though joints between dissimilar materials are weaker. Some moisture-absorbing plastics, such as polyamide, polycarbonate, polysulfone and thermoplastic polyesters, may suffer reduced weld strength if moisture is present at the weld under normal welding conditions; drying them beforehand improves weld strength.
    Spin welding is suitable for joining pipe to pipe, pipe base to pipe, and pin (stud, rod) to part. The welding surfaces can be flat, angled or V-shaped. A conical mating-surface design increases the circumferential joint length, improving joint strength with the added benefit of self-centering. Spin welding is simple and reliable, and much faster than butt fusion welding — for example, a 160 mm diameter pipe can be welded in 2 min, versus 18 min for butt fusion welding. Spin weld joints are stronger than butt-fusion joints because the weld area is much larger. No air enters during spin welding, preventing harmful oxidation of the molten material and producing excellent weld quality — a real advantage for welding heat-oxidation-sensitive plastics.
    A major disadvantage of spin welding is that it only works when at least one part is round. Misaligned spin weld parts can cause flash. Spin welding requires rigid part structures; soft plastics cannot be welded because they bend and shake easily, which hinders heat buildup. Once melting begins during spin welding, the relative motion must stop quickly so the weld can solidify under pressure; otherwise the weld will tear and weld strength will be low. Spin welding is limited to parts about 160 mm in diameter or less.